Complete Guide on How To Use Gel Blaster Guns
Share
Since more and more people joining the hobby of gel ball blasting, some of you may wanna know how to use gel blaster guns in a right way. This complete guide on how to use gel blasters will answer most common questions. For any gel blasting beginners, this article could be very useful for you guys.
How Does Gel Blaster Work?
A gel blaster is a toy gun that fires small water-absorbent gel balls. The gel balls are made from a polymer material that can absorb water. Before using this toy, you need to put these small spheres into a bowl with water. Then, they swell to a size of around 7-8mm when soaked for a few hours.
The gel ball blaster works by using a spring-loaded piston air pump to create air pressure. This air pressure is then used to propel the gel balls out of the gun's barrel. The muzzle velocity of a gel blaster is typically around 30-50fps, which is much lower than that of an airsoft gun. This makes gel blasters relatively safe to use, even for young children.
When the water beads hit their target, they burst and break down into small pieces. These pieces are water-soluble and will eventually dissolve in water. This makes gel blasters a relatively environmentally friendly toy.
Here is a more detailed explanation of how a gel blaster works:
- The gel balls are loaded into the gun's magazine.
- The spring-loaded piston air pump is cocked.
- The trigger is pulled, which releases the piston air pump.
- The air pressure from the piston air pump propels the gel balls out of the gun's barrel.
- The gel balls hit their target and burst.
- The pieces of the gel balls break down and dissolve in water.
Gel guns are a relatively safe and environmentally friendly toy that can be enjoyed by people of all ages. They are a great way to have fun and get some exercise.
How to Set Up A Gel Ball Blaster?
Here are the steps on how to set up a gel ball shooter:
- Read the instructions. This is the most important step, as it will tell you how to set up your specific gel blaster.
- Prepare the gel balls. Gel balls need to be hydrated before they can be used. The amount of time they need to hydrate will vary depending on the type of gel balls you are using. Typically, they need to be soaked in water for 4-6 hours, or overnight.
- Load the gel balls into the magazine. The magazine is the part of the gel blaster that holds the gel balls. There are different types of magazines, so make sure you know how to load the one that your gel blaster uses.
- Insert the battery. Most gel blasters use a battery to power the air pump. The battery compartment is usually located in the handle of the gel blaster.
- Turn on the gel blaster. There is usually a switch on the side of the gel blaster that you need to turn to the "on" position.
- Aim and shoot. Once the gel blaster is turned on, you can aim and shoot at your target.
Here are some additional tips for setting up a gel ball blaster:
- Use a clean, clear water to hydrate the gel balls. This will help them to swell evenly and prevent them from breaking.
- Do not overfill the magazine with gel balls. This can cause the gel balls to jam in the magazine.
- Make sure the battery is inserted correctly. If the battery is not inserted correctly, the gel blaster will not work.
- Wear eye protection when using a gel blaster. This will help to protect your eyes from the gel balls.
How to Assemble Gel Blaster?
Here are the steps on how to assemble a water beads gun:
- Gather your tools and materials. You will need a screwdriver, a pair of pliers, and the gel blaster itself.
-
Identify the different parts of the gel blaster. There are many different types of gel blasters, so the exact parts may vary. However, most gel blasters have the following parts:
- A barrel
- A magazine
- A trigger
- A grip
- A stock
- A battery
- A spring
- A piston
- Assemble the main body of the gel blaster. This may involve screwing the barrel, magazine, trigger, grip, and stock together.
- Insert the battery. The battery compartment is usually located in the handle of the gel blaster.
- Load the magazine with gel balls. The magazine is the part of the gel blaster that holds the gel balls. There are different types of magazines, so make sure you know how to load the one that your gel blaster uses.
- Test the gel blaster. Once the gel blaster is assembled, you should test it to make sure it works properly.
Additional tips for assembling a gelsoft:
- Be careful not to overtighten any screws. This can damage the gel blaster.
- Make sure the battery is inserted correctly. If the battery is not inserted correctly, the gel blaster will not work.
- Wear eye protection when assembling a gel blaster. This will help to protect your eyes from any flying parts.
Example of Disassembly a Gel Beads Gun:
How to Turn On Gel Blaster Guns?
The process of turning on a gel blaster may vary depending on the specific model. However, here are the general steps on how to turn on a gel blaster:
- Locate the power switch. The power switch is usually located on the side or top of the gel blaster.
- Turn the power switch to the "on" position. The power switch may be a toggle switch, a button, or a dial.
- If the gel blaster has a safety, make sure it is disengaged. The safety is usually located near the trigger.
- The gel blaster should now be turned on. You can test this by pulling the trigger. If the gel blaster fires, then it is turned on.
Here are some additional tips for turning on a gel blaster:
- Make sure the battery is inserted correctly. If the battery is not inserted correctly, the gel blaster will not work.
- If the gel blaster does not turn on, check the fuse. The fuse is usually located in the battery compartment.
- If the gel blaster still does not turn on, contact the manufacturer for assistance.
How to Charge Your Gel Blasters?
Gel blasters typically use rechargeable lithium-ion (Li-ion) batteries, which provide the necessary power for firing. To charge a gel blaster, you will need a charger that is compatible with the battery type used by your gel blaster.
Here are the steps on how to charge a gelsoft blaster:
- Locate the battery compartment. The gel blaster battery compartment is usually located in the handle of the gel blaster.
- Remove the battery from the gel blaster. Be careful not to touch the terminals of the battery with your bare hands.
- Connect the battery to the charger. The charger will have a connector that matches the charging port on the battery.
- Plug the charger into an electrical outlet. The charger will usually have a power cord that plugs into a standard wall outlet.
- Charge the battery for the recommended amount of time. The recommended charging time will vary depending on the battery type and the charger.
- Once the battery is fully charged, remove it from the charger. You can then insert the battery back into the gel blaster and start using it.
Here are some additional tips for charging a gel blaster battery:
- Use a charger that is compatible with the battery type used by your gel blaster. Using an incompatible charger can damage the battery.
- Do not overcharge the battery. Overcharging can damage the battery and shorten its lifespan.
- If the battery is not fully charged, it may not have enough power to fire the gel blaster.
- If the battery is damaged, do not use it. A damaged battery can pose a safety hazard.
How to Grow Orbeez for Splatter Ball Guns?
Steps on how to grow Orbeez for gel blaster:
- Gather your materials. You will need a bowl, water, Orbeez, and a timer.
- Fill the bowl with water. The amount of water you need will depend on the number of Orbeez you are growing.
- Add the Orbeez to the water. Make sure the Orbeez are completely submerged in the water.
- Set a timer for 4-6 hours. This is the amount of time it takes for Orbeez to fully hydrate.
- After 4-6 hours, the Orbeez should be fully hydrated. You can check this by squeezing one of the Orbeez. If it is soft and squishy, then it is fully hydrated.
- Drain the water from the bowl. You can do this by pouring the water out or using a colander.
- The Orbeez are now ready to use in your gel blaster. You can store them in an airtight container until you are ready to use them.
Tips for growing Orbeez for gel blaster:
- Use filtered or bottled water. This will help to prevent the Orbeez from absorbing any impurities from the water.
- Do not use hot water. Hot water can damage the Orbeez.
- If you are in a hurry, you can speed up the hydration process by using warm water. However, do not use boiling water.
- Once the Orbeez are fully hydrated, they will shrink slightly. This is normal.
- The Orbeez can be stored in an airtight container for up to 6 months.
How to Load Gel Guns?
Steps on how to load a gel blaster:
- Prepare the gel balls. Gel balls need to be hydrated before they can be used. The amount of time they need to hydrate will vary depending on the type of gel balls you are using. Typically, they need to be soaked in water for 4-6 hours, or overnight.
- Locate the magazine. The magazine is the part of the gel blaster that holds the gel balls. There are different types of magazines, so make sure you know how to load the one that your gel blaster uses.
- Open the magazine. There is usually a button or latch that you need to press or lift to open the magazine.
- Load the gel balls into the magazine. The gel balls should be loaded into the magazine in a single layer. Do not overfill the magazine, as this can cause the gel balls to jam.
- Close the magazine. Once the gel balls are loaded, close the magazine by pressing or lifting the button or latch.
- Insert the magazine into the gel blaster. The magazine should be inserted into the gel blaster until it clicks into place.
- The gel blaster is now loaded and ready to use.
Tips for loading a gel blaster:
- Use a clean, clear water to hydrate the gel balls. This will help them to swell evenly and prevent them from breaking.
- Do not overfill the magazine with gel balls. This can cause the gel balls to jam in the magazine.
- Make sure the magazine is inserted correctly. If the magazine is not inserted correctly, the gel blaster will not work.
- Wear eye protection when loading a gel blaster. This will help to protect your eyes from the gel balls.
Recommend loading your orbeez gun with a speedloader like this:
Should You Dry Fire Gel Ball Blasters?
No, you should not dry fire a gel blaster. Dry firing is the act of firing a gun without any ammunition. In the case of a gel blaster, this means firing the gun without any gel balls.
Dry firing a gel blaster can damage the gun. The firing pin can strike the barrel, which can cause the barrel to become damaged. The firing pin can also become damaged, which can prevent the gun from firing properly.
In addition, dry firing a gel blaster can be dangerous. The firing pin can strike the barrel with enough force to cause the barrel to break. This can send pieces of the barrel flying, which could injure someone.
For these reasons, it is important to never dry fire a gel blaster. If you need to practice your aim, you can use a laser pointer or a dry fire trainer.
In Conclusion
Gel blaster guns are a fun and safe way to enjoy the outdoors. They are also a great way to practice your aim and improve your hand-eye coordination.
In this blog post, we have covered everything you need to know about how to use gel ball blaster guns. We have discussed how to set up your gel blasters toy, how to load it, and how to fire it. We have also provided some safety tips to help you stay safe while using your gel blaster.
We hope you have found this guide on how to use gel blaster guns informative and helpful. If you have any further questions, please do not hesitate to contact us.
By following these tips, you can help to ensure that you have a safe and enjoyable experience using your gel blaster.
Read more:
What is a Gel Blaster Battey & How to do Maintenance?
Gel Balls Introduction & Growing Guide